Major Rebuild Kit for SURGE® ALAMO 60, 75, 100, 1400 Vacuum Pumps

$350.00 $270.00
(You save $80.00)
(No reviews yet) Write a Review
SKU:
7560R
Major Rebuild Kit for Alamo vacuum pumps 60 75, 100+ and 1400 - See detail image for actual pump.
 
Alamo 60 & 75 have inlet and outlet both on top of pump as pictured
Alamo 100+ has as side inlet and top outlet
 
For Surge Alamo vacuum pumps used in dairy barns and milking systems. This is a very common pump sold from the 1950s to 1999. However it can be easily confused with other 2 Alamo models.  please check vane dimensions before ordering
 
Major Rebuild Kit Includes;
  • Set of 4 high quality long life Kevlar vanes
  • Vane Dimensions;  7.25 inch length 2.5 inch high - Tapered on barrel side
  • Needle Bearing for Shaft Side
  • Bearing Race for Needle Bearing
  • Double row bearing for back side of pump
  • Shim set
  • O-ring set for end plate (Only fits later model pumps)
 
These parts DO NOT FIT Alamo 50 that had sealed bearings. 
 
Babson Surge Alamo Vacuum Pumps
 
Rebuild Instructions can be viewed and printed from the Manuals Tab above
 
 
The pump body is about 7.8 inches wide and the vanes measure 7.25 inches long.
 
The Alamo 60 had a 3.5 hp motor mounted on a horizontal stand. See detail picture and parts drawing for actual pump assembly
The Alamo 75 had a 4.5 hp motor mounted (now a 5 hp) on a horizontal stand. See detail picture and parts drawing for actual pump assembly
 
The Alamo 100+ had a 5.5 slow speed 1100 RPM motor mounted direct drive with a LoveJoy Coupler
 
 
Note the original 75+ surge motors were marked as 4.5 hp. The replacement surge motor from GEA (WestfaliaSurge) is a 5 hp motor. they are essentially the same motor pulling the same amp draw and have the special box on the back side to fit the alamo pump frames. Motor may be in stock.
 
100+ (1400) Alamo Vacuum pump specs (5.5 HP direct drive) side inlet top exhaust - see detail image - 52 CFM - 1150 RPM - 5.5 HP Direct Drive Motor (call for availability of motor)
 
100+ Alamo Vacuum pump specs (5.5 HP belt drive) side inlet top exhaust - see detail image
- 52 CFM
- 1150 RPM
- 10 inch pump pulley
- 6.75 inch Motor pulley
- 5.5 hp motor
 
75+ Alamo Vacuum pump specs (5 HP) top inlet top exhaust - see detail image
- 45 CFM - 940 RPM
- 10 inch pump pulley
- 5.25 inch Motor pulley -
5 hp motor (available at link below)
 
60+ Alamo Vacuum pump specs (3.5 HP) top inlet top exhaust - see detail image
 
- 32 CFM - xxx RPM
- 10 inch pump pulley
- 4.xx inch Motor pulley
- 3.5 hp motor
 
50+ Alamo Vacuum pump specs (2.4 HP)  Had Sealed Bearings.   This kit will not work for Alamo 50
- 26 CFM - xxx RPM
- 10 inch pump pulley
- 3.xx inch Motor pulley
- 2.4 hp motor
 
 
 
 
Related Items for Alamo 60, 75, 1400 - Some at links below;
 
7560R  Major Rebuild kit includes bearing race, seals, shims and the vanes in this listing (this item)
7560    Basic Rebuild kit includes vanes, bearings, seals, shims and vanes in this listing.
7550    Vane set of 4
 
7750-0014-834 Small Drain Flapper for Alamo 30 tank, SP11, SP22 vacuum tanks
R137400 Rebuilt Alamo 40+ pump head only
R137190 Rebuilt Alamo 60/75+ pump head with reclaimer
R137050 Rebuilt Alamo 100+ pump head with reclaimer
 
 
67214  Double Oiler for Alamo 40, 550, 60 & 75 only.  Does Not fit 30 or 100
67213  3 dripper Oil System for Surge Alamo 100+ vacuum pump
 
Parts that fit All Babson Surge Alamo Vacuum Pumps
 
7750-0210-636G Surge Alamo Vacuum Pump Oil
7750-0014-049  Gasket for 2 piece Surge Oil Reclaimer
 
7750-0214-865  Original Surge Air Filters for Vacuum Tank
7750-0020-440  Drain flapper for vacuum tank and exhaust pipe
7750-0014-889  Support for Rubber Drain Flapper 7750-0020-440
 
7510 Pump Pulley - 10 inch sheave
 
 
Call for availability of complete rebuilt pump system
 
 
 
March 2023